R6-2 is a residential zoning district governed by ZR 23-22, with residential far of 2.5, a maximum building height of 65 feet.
These are the figures the engine applies when it models a lot in R6-2. Where a rule differs between a narrow and a wide street, both are shown.
| Residential FAR | 2.5 | ZR 23-22 |
|---|---|---|
| Community facility FAR | 2.5 | ZR 23-22 |
| Commercial overlay FAR | 2 | ZR 33-121 |
| City of Yes (UAP) maximum FAR | 3 | ZR 27-16 |
| Base minimum — wide street | 30 ft | ZR 23-22 |
|---|---|---|
| Base maximum — wide street | 45 ft | ZR 23-22 |
| Max height — wide street | 65 ft | ZR 23-22 |
| Setback — wide street | 10 ft | ZR 23-22 |
| Base maximum — narrow street | 45 ft | ZR 23-22 |
| Max height — narrow street | 65 ft | ZR 23-22 |
| Setback — narrow street | 15 ft | ZR 23-22 |
| Max height with City of Yes affordability | 75 ft | ZR 23-432 |
| Front yard | 0 ft | ZR 23-45 |
|---|---|---|
| Side yard | 0 ft | ZR 23-46 |
| Rear yard | 20 ft | ZR 23-47 |
| Lot coverage — interior lot | 80% | |
| Lot coverage — corner lot | 100% |
| Dwelling unit factor | 680 sf per unit | ZR 23-52 |
|---|---|---|
| Minimum lot area, practical | 1,700 sf | |
| Parking spaces per dwelling unit | 0.5 | ZR 25-23 |
| MIH base FAR | 2.5 | ZR 27-131 |
| MIH maximum FAR where mapped | 3 | ZR 27-131 |
At 2.5 FAR, a 10,000 square foot lot in R6-2 carries roughly 25,000 square feet of zoning floor area, which at a 680 square foot dwelling unit factor is about 36 units.
That is the ceiling, not the answer. The height envelope, required yards, lot shape, street width, overlays and any special district all cut into it. Running the real lot is the only way to know which constraint binds first.
A section through the R6-2 envelope, drawn to scale from the figures in the table above. The solid shape is as of right; where the district carries a City of Yes uplift, the dashed outline is what affordable housing adds.
Diagrammatic. It shows the governing heights and the setback on a regular lot, not your lot: the sky exposure plane, lot shape, corner conditions and any overlay all reshape this in practice.
Every area of the city zoned R6-2, from NYC Planning’s published zoning district layer.
Use groups permitted in R6 districts:
R6-2 has a residential far of 2.5, set by ZR 23-22. On a 10,000 square foot lot that is about 25,000 square feet of zoning floor area before any bonus, and before the height envelope and yard requirements are applied.
The maximum building height in R6-2 is 65 feet on a wide street, with a street wall rising to between 30 and 45 feet before a required setback. Height is measured and applied under ZR 23-22.
Yes. Under the Universal Affordability Preference, R6-2 rises from 2.5 to 3 where the additional floor area is permanently affordable housing. That is an as-of-right increase, not a discretionary action.
Where MIH is mapped on a lot in R6-2, floor area rises from 2.5 to 3, a gain of 0.5. MIH applies only where the City has mapped it, so it is a property-by-property question rather than a district-wide one.
Source: NYC Planning zoning districts.